Nodes of different colours represent the following:
Solid arrows point from a parent (sub)module to the submodule which is descended from it. Dashed arrows point from a module being used to the module or program unit using it. Where possible, edges connecting nodes are given different colours to make them easier to distinguish in large graphs.
Nodes of different colours represent the following:
Solid arrows point from a procedure to one which it calls. Dashed arrows point from an interface to procedures which implement that interface. This could include the module procedures in a generic interface or the implementation in a submodule of an interface in a parent module. Where possible, edges connecting nodes are given different colours to make them easier to distinguish in large graphs.
Nodes of different colours represent the following:
Solid arrows point from a procedure to one which it calls. Dashed arrows point from an interface to procedures which implement that interface. This could include the module procedures in a generic interface or the implementation in a submodule of an interface in a parent module. Where possible, edges connecting nodes are given different colours to make them easier to distinguish in large graphs.
SUBROUTINE ReportThermalChimney
! SUBROUTINE INFORMATION:
! AUTHOR Kwang Ho Lee
! DATE WRITTEN April 2008
! MODIFIED na
! RE-ENGINEERED na
! PURPOSE OF THIS SUBROUTINE:
! This subroutine fills remaining report variables.
! METHODOLOGY EMPLOYED:
! na
! REFERENCES:
! na
! USE STATEMENTS:
USE DataHVACGlobals, ONLY: TimeStepSys
IMPLICIT NONE ! Enforce explicit typing of all variables in this routine
! SUBROUTINE ARGUMENT DEFINITIONS:
! na
! SUBROUTINE PARAMETER DEFINITIONS:
! na
! INTERFACE BLOCK SPECIFICATIONS
! na
! DERIVED TYPE DEFINITIONS
! na
! SUBROUTINE LOCAL VARIABLE DECLARATIONS:
INTEGER :: ZoneLoop ! Counter for the # of zones (nz)
REAL(r64) :: AirDensity
REAL(r64) :: CpAir
REAL(r64) :: TSMult
TSMult=TimeStepSys*SecInHour
DO ZoneLoop = 1, NumOfZones ! Start of zone loads report variable update loop ...
! Break the infiltration load into heat gain and loss components.
AirDensity = PsyRhoAirFnPbTdbW(OutBaroPress,MAT(ZoneLoop),ZoneAirHumRat(ZoneLoop))
CpAir = PsyCpAirFnWTdb(ZoneAirHumRat(ZoneLoop),MAT(ZoneLoop))
ZnRptThermChim(ZoneLoop)%ThermalChimneyVolume = (MCPThermChim(ZoneLoop)/CpAir/AirDensity)*TSMult
ZnRptThermChim(ZoneLoop)%ThermalChimneyMass = (MCPThermChim(ZoneLoop)/CpAir)*TSMult
ZnRptThermChim(ZoneLoop)%ThermalChimneyHeatLoss = 0.0d0
ZnRptThermChim(ZoneLoop)%ThermalChimneyHeatGain = 0.0d0
IF (ZT(ZoneLoop) > Zone(ZoneLoop)%OutDryBulbTemp) THEN
ZnRptThermChim(ZoneLoop)%ThermalChimneyHeatLoss = MCPThermChim(ZoneLoop)*(ZT(ZoneLoop)-Zone(ZoneLoop)%OutDryBulbTemp)* &
TSMult
ZnRptThermChim(ZoneLoop)%ThermalChimneyHeatGain=0.0d0
ELSE IF (ZT(ZoneLoop) <= Zone(ZoneLoop)%OutDryBulbTemp) THEN
ZnRptThermChim(ZoneLoop)%ThermalChimneyHeatGain = MCPThermChim(ZoneLoop)*(Zone(ZoneLoop)%OutDryBulbTemp-ZT(ZoneLoop))* &
TSMult
ZnRptThermChim(ZoneLoop)%ThermalChimneyHeatLoss =0.0d0
END IF
END DO ! ... end of zone loads report variable update loop.
RETURN
END SUBROUTINE ReportThermalChimney